Microscan EZ Match Imager Manual de usuario descargar pdf (Pagina 2)

Step 6 —

Select Protocol and

Connect

• Choose the connection protocol you are using and click Connect.

• Once you select your communications mode, follow the simple prompts

to establish your connection.

• When you are connected, you will see the green connection indicator in

the status bar at the bottom right of your screen.

USB:

RS-232:

Step 9 — Test Read Rate

Read Rate indicates the number of tube/cap detections or successful

decodes per second achieved by the imager.

Test Read Rate by EZ Button

1. To start the Read Rate test, hold down

the EZ Button about three seconds

until you hear three short beeps. The

20%

40%

, and

60%

LEDs will illuminate.

While the object is being inspected, the

Read Rate LEDs will indicate the read

rate percentage on the back of the unit.

2. To end the Read Rate test, press the

EZ B

utton and quickly release.

Test Read Rate by ESP

1. Click the Test button to start the Read Rate test and Stop to end it.

If a tube or cap has been successfully detected, or a symbol has been

successfully decoded, the object’s data and related features will be

presented in the field below the image display window. Also, while the

object is being inspected, the Read Rate LEDs will indicate the Read

Rate percentage on the back of the unit.

2. To end the test, click the Stop button.

Note: Read Rate can also be tested using the Read Rate interface in

Utilities.

Test Read Rate by Serial Command

You can also start a test with the <C> or <Cp> command and end it with the

<J> command.

Step 10 — Configure the Imager

To make setup changes to the EZ Match Imager, click the App Mode button.

The following modes are accessible by clicking the buttons in the first row of

App Mode icons:

• Click the EZ Mode button to return to EZ Mode.

• Click the Autoconnect button to establish communication.

• Click the Send/Recv button to send or receive commands.

• Click the Switch Model button to open the model menu, or to return to a

previous model.

•Click the EZ Match button to Test the imager and to configure Multi-Operation

settings, tube/cap Library settings, and tube/cap detection Messages.

•

Click the

Parameters

button to show the tabbed tree controls for Communication,

Read Cycle, Symbologies, I/O Parameters, Symbol Quality, Matchcode, and

Diagnostics.

• Click the Setup button to access a Camera Setup tree control and Video

view, Evaluate image captures, Calibrate the imager, set the Window of

Interest, fine-tune capture settings and processing settings in the IP Database,

set up output filters and parse symbol data in Ordered Output and Output

Format, and control multiple read cycle functions in Dynamic Setup.

• Click the Terminal button to display tube or cap detection data or decoded

symbol data, and to send serial commands to the imager using text or macros.

•Click the Utilities button to test Read Rate, request or clear Counters, enable

or disable the imager or send output pulses in Device Control, determine the

Differences from Default in the current settings, add or remove master symbol

data in Master Database, and verify or update the imager’s Firmware.

For further details, see ESP Help in the dropdown Help menu.

Step 8 — Calibrate

EZ Match settings can be adjusted automatically for optimum tube/cap

detection and symbol decoding performance by either the EZ Button or by

ESP

During the calibration routine, the imager will flash its amber Read Rate

percent LEDs and red illumination LEDs while searching camera settings

and determining the best configuration for detecting tubes or caps, or for

decoding symbol data. Upon successful completion of this routine, a green

LED pattern will flash brightly and illuminate the object. If unsuccessful, the

imager will emit 5 short beeps and stop searching.

Calibrate by EZ Button

1. Hold down the EZ Button for about two seconds and release when you

hear two short beeps. The 20% and 40% LEDs will illuminate.

The imager will search camera settings to determine the best configuration

for detecting tubes or caps, or for decoding symbol data.

Note: To end all EZ Button functions, press the EZ Button once and

quickly release.

Calibrate by ESP

1. Click the Calibrate button.

The imager will search camera settings to determine the best configuration

for detecting tubes or caps, or for decoding symbol data.

A successful calibration will display a green frame around the object,

and the following message will appear: “Uploading all reader parameters.”

After a moment the tube/cap data and/or symbol data will be presented

in the field below the image display window.

Calibrate by Serial Command

Send <@CAL> from a terminal program to begin calibration.

Step 11 — Save Configuration

To make changes to a configuration setting:

• Send, No Save. Changes will be lost when power is re-applied to the

imager.

• Send and Save. This activates all changes in current memory and saves

to the imager for power-on.

1. Left click on the

+ t

o expand the

desired tree.

2. Double click on

the desired

parameter and

click once in the

selection box to

view options.

5. Right click on the

open screen and

select Save to

Reader to implement

the command in the

imager.

4. Left click on the

en screen to

complete your

selection.

3. Place your cursor

in the selection

box, scroll down to

the setting you

want to change,

and click once on

the setting.

Saving Options

Step 7 —

Locate the Object

Locate the Object by ESP

•In ESP’s EZ Mode, click the Locate button to enable the blue target pattern.

The object in the field of view will appear in the video view beneath the

Locate

and

Calibrate

buttons, and you will see the blue target

pattern projected

from the front of the imager.

• Center the target pattern on the object.

At 2 to 3 inches, the pattern resembles an X. At 3 to 6 inches, the pattern

resembles a V.

Important: The entire object of interest (tube, cap, or symbol) should fall

within the field of view (FOV) of the imager. The field of view is what appears

in ESP’s Locate/Calibrate window in EZ Mode.

• Click the Stop button to end the Locate function.

Locate the Object by EZ Button

If you are not connected to a host computer, the EZ Button allows you to locate

an object in the imager’s field of view.

• Hold down the EZ Button for about one second and release when you hear

one short beep. The amber 20% LED will illuminate, and you will see the

blue target pattern projected from the front of the imager.

• Center the target pattern on the object.

Note: To end all EZ Button functions, press the EZ Button once and quickly

release.

1 2

EZ Match Imager 1

Comentarios a estos manuales

Sin comentarios

Microscan EZ Match Imager Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Lectores De Códigos De Barras Microscan EZ Match Imager