Microscan MS-Q Imager Manual de usuario Pagina 9
- Pagina / 250
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
MS-Q Imager User’s Manual ix
Introduction
Statement of Agency Compliance
The MS-Q has been tested for compliance with FCC regulations and was found to be
compliant with all applicable FCC Rules and Regulations.
IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, this
device must not be co-located or operate in conjunction with any other antenna or transmitter.
CAUTION: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
The MS-Q has been tested for compliance to CE (Conformité Européenne) standards and
guidelines and was found to conform to applicable CE standards, specifically the EMC
requirements EN 55024, ESD EN 61000-4-2, Radiated RF Immunity EN 61000-4-3, ENV
50204, EFT EN 61000-4-4, Conducted RF Immunity EN 61000-4-6, EN 55022, Class B
Radiated Emissions, and Class B Conducted Emissions.
The MS-Q can be set to use targeting lasers. The MS-Q’s targeting laser emits Class 2M
radiation outside of the product per IEC 60825-1. Class 2M Laser/LED product. Do not
stare into the beam or view directly with optical instruments.
The MS-Q has been tested by an independent electromagnetic compatibility laboratory in
accordance with the applicable specifications and instructions.
Laser/LED Radiation
Wavelength: <1mW
Maximum Output: 650-700 nm
Laser Pulse Duration: 0.977 mSec.
LED Pulse Duration: 0.255 uSec.
- MS-Q Imager 1
- User’s Manual 1
- Disclaimer 2
- Latest Manual Version 2
- Technical Support 2
- What Is Covered? 3
- What Is Excluded? 3
- Limitation of Liability 3
- Table of Contents 4
- Introduction 5
- Chapter 6 I/O Parameters 5
- Chapter 7 Advanced Operations 5
- About the MS-Q Imager 7
- About This Manual 7
- Highlighting 7
- Product Labels 8
- MS-Q Imager User’s Manual ix 9
- Statement of RoHS Compliance 10
- Warning and Caution Summary 11
- 1 Quick Start 13
- Check Required Hardware 14
- Assemble the Imager 15
- Grasp the connection 17
- USB Interface 18
- PS/2 Interface 19
- RS-232 Interface 20
- Bluetooth Interface 21
- Batch/Battery Interface 22
- Install ESP 23
- Select Model 24
- 2 Using ESP 27
- 2-2 MS-Q Imager User’s Manual 28
- Application Mode 29
- Tree Controls 30
- Menu Toolbar 31
- New Model 32
- Preferences > General Tab 33
- Terminal Tab 34
- Bar Code Options Tab 35
- Advanced Tab 36
- Document Memo 37
- Model Memo 37
- Connect 38
- Barcode Dialog 39
- Send/Receive 40
- Advanced Options 41
- 3 Basic Operations 43
- Step 1 — Practice Targeting 44
- MS-Q Imager User’s Manual 3-3 45
- ABCDEFGHIJKLMNOP 45
- Handle Trigger 49
- Left Button 49
- Right Button 49
- Continuous Read 49
- USB Battery Charge Mode 50
- 4 Communications 51
- Communications by ESP 52
- Communications Overview 53
- Parity (RS-232) 57
- Stop Bits (RS-232) 57
- Data Bits (RS-232) 57
- Timeout Settings (Cabled) 57
- Disconnect 59
- Auto-Connect 59
- One-Way Mode Options 60
- Bluetooth Access 61
- Bluetooth Access by ESP 61
- Sleep Mode Timeout 62
- Out-of-Range Notification 63
- Lockout Link Mode 64
- Batch/Battery 66
- Batch Mode Options 67
- Reconnecting to the Host 67
- Auto-Transfer Buffer Memory 68
- RS-232 Batch Features 69
- Preamble 70
- Postamble 71
- Preamble and Postamble by ESP 72
- Keyboard Mapping 73
- Text Commands 74
- Time Stamp 75
- Reader Packet Format 76
- Reader to Host Packet Size 76
- Expect Host Response 76
- Reader Send Retry Count 76
- Host Acknowledgement Timeout 76
- Store If Not Connected 77
- Reconnect Timeout 77
- Max Connection Wait Time 77
- 5 Symbologies 79
- Symbologies by ESP 80
- Aztec by ESP 81
- Codabar 82
- Codablock F 83
- Code 11 by ESP 84
- Code 39 85
- Code 39 by ESP 86
- Code 93 87
- Code 128 88
- Composite 89
- Data Matrix 90
- Interleaved 2 of 5 91
- Maxicode 92
- Matrix 2 of 5 93
- MicroPDF417 94
- MSI Plessey 95
- NEC 2 of 5 96
- PDF417 by ESP 97
- Pharmacode 98
- Pharmacode (cont.) 99
- Pharmacode by ESP 99
- Postal Symbologies 100
- Postal Symbologies by ESP 101
- QR Code by ESP 102
- GS1 DataBar 103
- UPC/EAN/JAN 104
- Symbology Identifier 105
- 6 I/O Parameters 107
- I/O Parameters by ESP 108
- Laser Target 109
- Illumination 110
- MS-Q Operational Feedback 111
- Handle Trigger Programming 112
- Left Button Programming 112
- Right Button Programming 113
- Beep and Vibrate Settings 114
- Automatic Gain Control (AGC) 115
- Minimum Gain 116
- Maximum Gain 116
- Gain Break Point 116
- LightRay Optics 117
- Assembly (100 Series) 118
- Assembly (200 Series) 118
- Reading Symbols (100 Series) 119
- Reading Symbols (200 Series) 119
- LightRay Optics by ESP 120
- 7 Advanced Operations 121
- Dual Optics 122
- VGA and Megapixel Settings 123
- Select Region of Interest 124
- Set Targeting Zone Tolerances 125
- IP Modes 126
- Trigger Optimization 127
- Global Optimization 128
- Handle Trigger Optimization 129
- Left Button Optimization 130
- Right Button Optimization 131
- MS-Q Imager User’s Manual 132
- High and Low Density Symbols 133
- Near and Far Field 133
- High Density Symbols 134
- Near Field 134
- Low Density Symbols 134
- Far Field 134
- Trigger Optimization by ESP 135
- Trigger/Button Configuration 136
- Trigger/Button Summary 137
- Continuous Operations 138
- Symbol Background 140
- Set Decode Time 141
- Button Stay-Down Time 142
- Mirroring 143
- Motion Detection 144
- Auto White Balance 145
- Symbol Readability Index 146
- Terminal 147
- Terminal View 148
- MS-Q Imager User’s Manual 8-3 149
- Editing a Macro 151
- Terminal Right-Click Menu 152
- Terminal Dropdown Menu 153
- 8-8 MS-Q Imager User’s Manual 154
- 9 Utilities 155
- Image Upload 156
- Device Control 157
- Differences from Default 158
- Firmware 159
- Imager ID 160
- Bluetooth 161
- Advanced 162
- Unique Item Identifiers 163
- UII Overview 164
- Non-UII Characters 165
- UII Mode Features 166
- UII Mode Settings by ESP 167
- Error Messaging 168
- Valid Formats 170
- Appendices 171
- A-2 MS-Q Imager User’s Manual 172
- General Specifications 172
- A-4 MS-Q Imager User’s Manual 174
- Electrical Specifications 174
- USB Cable Pinouts 175
- RS-232 Cable Pinouts 176
- Configuration Symbols 178
- A-8 MS-Q Imager User’s Manual 178
- ,” Command - Dump 188
- Battery Charger Kit 233
- MS-Q Battery Charger Options 234
- Install Cable 235
- Read Quick Connect Code 235
- Establish Mode 235
- Modem Firmware Version 236
- Keyboard Input (USB and PS/2) 237
- Appendix J — MS-Q Maintenance 238
- Hyperlink Index 239
- 2 MS-Q Imager User’s Manual 240
- D Index 241
- 4 MS-Q Imager User’s Manual 242
- G Index 243
- 6 MS-Q Imager User’s Manual 244
- M Index 245
- 8 MS-Q Imager User’s Manual 246
- Q Index 247
- 10 MS-Q Imager User’s Manual 248
- T Index 249
- 12 MS-Q Imager User’s Manual 250
Comentarios a estos manuales
Relacionado con productos y manuales para Lectores De Códigos De Barras Microscan MS-Q Imager
(10 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Our premium databases for XRumer and GSA Search Engine Ranker are just what you need! What do our databases include? • Active links: Get access to constantly updated lists of active links from profiles, posts, forums, guestbooks, blogs, and more. No more wasting time on dead links! • Verified and identified links: Our premium databases for GSA Search Engine Ranker include verified and identified links, categorized by search engines. This means you get the highest quality links that will he