Microscan Quadrus MINI Manual de usuario descargar pdf (Pagina 2)

Step 6 —

Connect

To connect using the Connection Wizard:

• Click Connect on the menu toolbar, and then select Connection Wizard.

• Select RS-232 or USB.

• Configure settings as required by the application, and click Connect.

• When a connection is established, the green indicator in the status bar at

the bottom right of the screen will be visible:

Important: The imager is in Continuous Read Mode by default. For

best connection results, be sure that no decodable symbols are within the

imager’s field of view while attempting to connect.

Step 9 — Test Read Rate

Read Rate indicates the number of successful decodes per second

achieved by the imager.

Test Read Rate by EZ Button

1. To start the Read Rate test, hold down

the EZ Button about three seconds

until you hear three short beeps. The

20%

40%

, and

60%

LEDs will illuminate.

While the object is being inspected, the

Read Rate LEDs will indicate the read

rate percentage on the back of the unit.

2. To end the Read Rate test, press the

EZ Button and quickly release.

Test Read Rate by ESP

1. Click the Test button to start the Read Rate test and Stop to end it.

If a symbol has been successfully decoded, its data and related features

will be presented in the field below the image display window. Also,

while the object is being inspected, the Read Rate LEDs will indicate

the Read Rate percentage on the back of the unit.

2. To end the test, click the Stop button.

Note: Read Rate can also be tested using the Read Rate interface in

Utilities.

Test Read Rate by Serial Command

You can also start a test with the <C> or <Cp> command and end it with the

<J> command.

Step 7 — Locate the Symbol

Locate by ESP

•In ESP’s EZ Mode, click the Locate button to enable the blue target pattern.

The symbol in the field of view will appear in the video view beneath the

Locate

and

Calibrate

buttons, and you will see the blue target

pattern projected

from the front of the imager.

• Center the target pattern on the symbol.

At 2 to 3 inches, the pattern resembles an X. At 3 to 6 inches, the pattern

resembles a V.

Important: The entire symbol should fall within the field of view (FOV) of the

imager. The field of view is what appears in ESP’s Locate/Calibrate window

in EZ Mode.

• Click the Stop button to end the Locate function.

Locate by EZ Button

If you are not connected to a host computer, the EZ Button allows you to locate

the symbol in the imager’s field of view.

• Hold down the EZ Button for about one second and release when you hear

one short beep. The amber 20% LED will illuminate, and you will see the

blue target pattern projected from the front of the imager.

• Center the target pattern on the symbol.

Note: To end all EZ Button functions, press the EZ Button once and quickly

release.

Step 10 — Configure the Imager

in ESP

Click the App Mode button to make configuration changes to the imager.

The following modes are accessible by clicking the buttons at the top of the

screen:

• Click the EZ Mode button to return to EZ Mode.

• Click the Autoconnect button to establish communication.

• Click the Send/Recv button to send or receive commands.

• Click the Switch Model button to open the model menu, or to return to a

previous model.

•

Click the

Parameters

button to show the tabbed tree controls for Communication,

Read Cycle, Symbologies, I/O Parameters, Symbol Quality, Matchcode, and

Diagnostics.

• Click the Setup button to access a Camera Setup tree control and Video

view, Evaluate image captures, Calibrate the imager, set the Window of

Interest, load capture settings and processing settings in the Configuration

Database, set up output filters and parse symbol data in Ordered Output and

Output Format, and control multiple read cycle functions in Dynamic Setup.

• Click the Terminal button to display decoded

symbol data, and to send serial

commands to the imager using text or macros.

• Click the Utilities button to test Read Rate, request or clear Counters,

enable or disable the imager or send output pulses in Device Control, determine

the Differences from Default in the current settings, add or remove master

symbol data in Master Database, and verify or update the imager’s Firmware.

For further details, see ESP Help in the dropdown Help menu.

Step 8 — Calibrate

Imager settings can be adjusted automatically for optimum performance by

either the EZ Button or by ESP.

During the calibration routine, the imager will flash its Read Rate percent

LEDs and illumination LEDs while searching camera settings and determining

the best configuration for decoding symbol data. Upon successful completion

of this routine, a green LED pattern will flash brightly and illuminate the symbol.

If unsuccessful, the imager will emit 5 short beeps and stop searching.

Calibrate by EZ Button

1. Hold down the EZ Button for about two seconds and release when you

hear two short beeps. The 20% and 40% LEDs will illuminate.

The imager will search camera settings to determine the best configuration

for decoding symbol data.

Note: To end all EZ Button functions, press the EZ Button once and

quickly release.

Calibrate by ESP

1. Click the Calibrate button.

The imager will search camera settings to determine the best configuration

for decoding symbol data.

A successful calibration will display a green frame around the symbol,

and the following message will appear: “Uploading all reader parameters.”

After a moment the symbol data will be presented in the field below the

image display window.

Calibrate by Serial Command

Send <@CAL> from a terminal program to begin calibration.

Step 11 — Save Changes in ESP

To make changes to a configuration setting:

• Send, No Save. Changes will be lost when power is re-applied to the

imager.

• Send and Save. This activates all changes in current memory and saves

to the imager for power-on.

1. Left-click on the

+ to expand the

desired tree.

2. Double-click on

the desired

parameter and

click once in the

selection box to

view options.

5. Right-click on the

open screen and

select Save to

Reader to implement

the command in the

imager.

4. Left-click on the

open screen to

complete your

selection.

3. Place your cursor

in the selection

box, scroll down to

the setting you

want to change,

and click once on

the setting.

Saving Options

1 2

Quadrus MINI 1

Comentarios a estos manuales

Sin comentarios

Microscan Quadrus MINI Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Lectores De Códigos De Barras Microscan Quadrus MINI