Microscan MS-4 Especificaciones Pagina 66
- Pagina / 202
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Multisymbol
4-18 MS-3 Laser Scanner User’s Manual
4–Read Cycle/Trig-
Multisymbol
Number of Symbols
Definition: Multisymbol allows the user to define up to six bar code symbols that
can be read in a single read cycle.
Usage: Multisymbol is commonly used in shipping applications where a ship-
ping symbol contains individual symbols for part number, quantity, etc.
This feature allows one trigger to pick up all the symbols. AIAG and
UCC/EAN- 128 are two application standards that address this need.
Conditions The following conditions apply:
1. All noread messages are posted at the end of the data string.
2. If more than one symbol is within the scan beam at the same time,
symbol data may not be displayed in the order of appearance.
3. If Matchcode Type is set to Sequential or if Trigger is set to
Continuous Read 1 Output, Number of Symbols will default to
1 (if set to any number greater than 1).
4. The maximum number of characters in any one bar code (other
than PDF417) is 64.
5. The maximum number of characters in a single scan line is 102
(Code 39).
6. The maximum number of characters for all symbols is 392, includ-
ing preamble, separators, and LRC.
Definition: Number of Symbols is the number of different symbols that can be
read in a single read cycle.
Serial Cmd: <K222,number of symbols,multisymbol separator>
Default: 1
- MS-3 Laser Scanner 1
- Microscan Systems, Inc 2
- Microscan Europe 2
- Microscan Asia Pacific R.O 2
- Table of Contents 4
- Chapter 11 Utilities 6
- List of Figures 7
- List of Tables 7
- About the MS-3 Laser Scanner 9
- About This Manual 9
- Host Communications 9
- Highlighting 9
- Product Labels 10
- Warning and Caution Summary 11
- Quick Start 13
- Step 1 — Hardware Required 14
- Step 2 — Connect the System 15
- 1–Quick Start 16
- Quick Start 17
- Step 5 — Start Calibration 18
- Step 6 — Test for Read Rate 19
- Step 7 — Save Settings 20
- Communications 21
- 2–Communications 22
- Communications 23
- Host Port Parameters 24
- RS422 Status 25
- Auxiliary Port 26
- Transparent Mode 27
- Half Duplex Mode 28
- Full Duplex Mode 29
- Daisy Chain Mode 30
- Command Processing Mode 32
- Daisy Chain ID Status 34
- Daisy Chain ID 34
- Protocol 35
- Protocol By Serial Command 36
- Protocol by Embedded Menu 37
- Point-to-Point with RTS/CTS 39
- Polling Mode D 40
- Multidrop 40
- User Defined Point-to-Point 40
- Protocol 41
- User Defined Multidrop 42
- Response Timeout 44
- Intercharacter Delay 45
- Preamble Characters 46
- Postamble Characters 47
- 3–Protocol 48
- Read Cycle/Trigger 49
- Read Cycle by Serial Command 50
- Read Cycle by Embedded Menu 51
- Trigger Mode 52
- Continuous Read 1 Output 53
- External Trigger Level 54
- External Trigger Edge 55
- Serial Data 56
- Serial Data or External Edge 56
- Trigger Filter Duration 57
- External Trigger State 58
- Serial Trigger Character 59
- 4–Read Cycle/Trig 60
- Read Cycle/Trigger 61
- Good Decode Reads 62
- Read Cycle 63
- New Trigger 64
- Timeout or New Trigger 64
- Timeout Duration 65
- Multisymbol 66
- Multisymbol Separator 67
- Symbology 69
- Symbology by Embedded Menu 70
- Symbology by Serial Command 71
- Autodiscriminate 72
- Narrow Margins 73
- Symbology ID 74
- Background Color 75
- Code 39 Status 76
- Check Digit Status (Code 39) 76
- Check Digit Output (Code 39) 76
- Symbology 77
- Full ASCII Set (Code 39) 78
- Fixed Symbol Length (Codabar) 80
- Interleaved 2 of 5 82
- 5–Symbology 84
- Separator Status (UPC/EAN) 86
- Code 128 88
- UCC/EAN-128 89
- Code 93 Status 92
- Fixed Code Length (Code 93) 92
- Pharmacode 93
- Bar Widths (Pharmacode) 94
- Matchcode 95
- Matchcode by Serial Command 96
- Matchcode by Embedded Menu 97
- Overview of Matchcode 98
- Using Master Symbols 99
- Matchcode Type 100
- Match Start Position 101
- Match Length 101
- Wild Card Character 102
- Sequence On Noread 103
- Sequence On Mismatch 104
- Master Symbol Database 105
- Request Master Symbol Data 106
- Delete Master Symbol Data 107
- New Master Pin 108
- Scanner Setup 109
- 7–Scanner Setup 110
- Scanner Setup 111
- Scan Speed 112
- Laser On/Off Status 113
- Laser Framing 114
- Laser On Position 115
- Laser Off Position 116
- Laser Power 117
- Automatic Gain Control 118
- AGC Minimum 119
- AGC Maximum 119
- Transition Counter 120
- Bar Detection 121
- Data Outputs 123
- 8–Data Outputs 124
- Data Outputs 125
- Symbol Output 126
- When to Output Symbol Data 127
- As Soon As Possible 128
- End of Read Cycle 128
- Message Output 129
- Noread Message 130
- Bad Symbol Message 131
- No Symbol Message 132
- Serial Verification 133
- Control/Hex Output 134
- Operational Command Output 134
- Quality Output 135
- Partial Output 136
- Beeper Output 137
- Discrete I/O 139
- 9–Discrete I/O 140
- Discrete I/O 141
- Output 1 142
- Output Polarity 143
- Pulse Width 143
- Number to Output On 143
- Output 2 144
- Output 3 144
- Diagnostics 145
- Diagnostics by Serial Command 146
- Diagnostics by Embedded Menu 147
- Warning Messages Overview 148
- Warning Message Status 149
- Laser High Warning 150
- Laser Low Warning 151
- NOVRAM Corrupt Warning Status 152
- Power-on Count 153
- Time Since Last Reset 154
- Utilities 155
- Utilities by Serial Command 156
- Utilities 157
- Counters 158
- Part Number 159
- Checksum 160
- Read Rate 161
- Device Control 162
- Symbol Type 164
- Defaulting/Saving/Resetting 165
- Factory Default Parameters 166
- Default/Reset Definitions 166
- Code Types Enable Commands 167
- Scanner Status Requests 168
- Appendices 169
- A–Appendices 170
- Appendices 171
- Scanner Pin Assignments 172
- Caution: 172
- Serial Utility Commands 176
- Appendix F — ASCII Table 178
- Customer Default Parameters 180
- Hardware Default 182
- Reader Status Requests 183
- Entering Symbol Configuration 184
- Using Configuration Symbols 184
- Appendix I — Object Detector 186
- Appendix K — Operational Tips 189
- Appendix L — Embedded Menus 190
- Polling Sequence 194
- Select Sequence 195
Relacionado con productos y manuales para Lectores De Códigos De Barras Microscan MS-4
(390 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales