Microscan MS-2 Manual de usuario Pagina 100
- Pagina / 125
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
A-2 MS-2 CCD Reader User’s Manual
General Specifications
Appendix A — General Specifications
Mechanical
Height: 0.85” (21.6 mm)
Width: 1.75” (44.5 mm)
Length: 1.75” (44.5 mm)
Weight: 2 oz. (57 g)
Design
Sensor: CCD linear image sensor
Optics: 660 nm visible LED
Scanning Performance
Scan Rate: 220 scans/sec
Min. X Dimension: Down to 0.084 mm (3.3 mil) on
Code 39
Depth of Field: 0.8 to 325 mm (12.8”)
Symbol Width: Up to 178 mm (7”) on 0.5 mm (20
mil) symbol
Communications
Interface: RS-232
Connector
Type: 3-foot cable terminated with 15-Pin High
Density D-sub Socket Connector
Symbologies
UPC/EAN, Code 39, Code 128/EAN-128, Interleaved
2 of 5, Industrial 2 of 5, Codabar, Code 93, MSI
Code, Plessey Code, GS1 DataBar (RSS)
Environmental
Operating Tempurature:
–20° to 50° C (–4° to 122° F)
Storage Tempurature:
–20° to 60° C (–4° to 140° F)
Relative Humidity: 20% to 85% (non-condensing)
Ambient Light: Works in any lighting conditions,
from 0 to 70,000 lux
CE Mark
Immunity Designed for: EN 55024:1998 ITE
Immunity Standard
Radiated and Conducted Emissions Designed for:
EN 55022:1998 ITE Disturbances Class A
Electrical
Power: 5V +/– 5%, 300 mV p-p max. ripple,
150mA @ 5V (typ.)
Discrete I/O
Trigger Input:
4.7 to 24V rated (0 µA @ 5V – 600 µA
@ 0V)
MS-2 CCD Reader Dimensions
Standard Case, Side
Standard
Case, Base
Right Angle
Case, Side
Right Angle Case, Base
- MS-2 CCD Reader 1
- User’s Manual 1
- Disclaimer 2
- Latest Manual Version 2
- Technical Support 2
- What Is Covered? 3
- What Is Excluded? 3
- Limitation of Liability 3
- Table of Contents 4
- About the MS-2 CCD Reader 6
- About This Manual 6
- Highlighting 6
- Host Communications 6
- Warning and Caution Summary 7
- Statement of RoHS Compliance 9
- MS-2 CCD Reader User’s Manual 10
- 1 Quick Start 11
- Step 1 — Check Hardware 12
- Step 2 — Connect the System 13
- Step 3 — Install ESP 14
- Step 4 — Select Model 15
- Step 5 — Autoconnect 16
- Step 6 — Position the Reader 17
- Step 7 — Configure the Reader 18
- Saving Options 19
- Save Configuration in ESP 20
- 2 Using ESP 21
- Application Mode 23
- Menu Toolbar 24
- Preferences > General Tab 26
- Preferences > Terminal Tab 27
- Sizing Information 28
- Preferences > Advanced Tab 29
- (cont.) 30
- Connect to Readers via TCP/IP 30
- Use Default Storage Location 30
- Document Memo 31
- Model Memo 31
- Autoconnect 32
- Autoconnect (cont.) 33
- Navigating in ESP 35
- Send/Receive Options 36
- Defaulting 37
- Advanced Options 37
- 3 Communications 39
- Communications by ESP 40
- Host Port Connections 42
- Host Port Protocol 43
- Preamble 44
- Postamble 45
- 4 Read Cycle 47
- Read Cycle by ESP 48
- Read Cycle Serial Commands 49
- MS-2 Read Cycle Overview 50
- Number of Symbols 51
- Trigger Mode 53
- External Edge 54
- Serial Data 54
- Serial Data and Edge 54
- No Decode Timeout 59
- Decodes Before Output 60
- No Read Message 61
- Reader Setup 62
- 5 Symbologies 63
- Symbologies by ESP 64
- Symbologies Serial Commands 65
- Full ASCII Set (Code 39) 67
- Symbol Length (Codabar) 69
- Interleaved 2 of 5 70
- Minimum Length 71
- Fixed Length 71
- Code 128/EAN 128 72
- GS1 DataBar (RSS) 74
- MSI Code 75
- Plessey Code 76
- Industrial 2 of 5 77
- UPC-A Status (UPC/EAN) 79
- UPC-E Status (UPC/EAN) 79
- EAN-8 Status (UPC/EAN) 79
- EAN-13 Status (UPC/EAN) 80
- UPC-A as EAN-13 (UPC/EAN) 81
- UPC-E as UPC-A (UPC/EAN) 81
- EAN-8 as EAN-13 (UPC/EAN) 81
- Symbology Identifier 82
- Terminal 83
- Terminal Window 84
- Editing a Macro 87
- Terminal Window Menus 88
- Utilities 89
- Serial Utility Commands 90
- Differences from Default 91
- Firmware 92
- Firmware Verification 94
- Device Control 95
- Default/Reset/Save 96
- Reader Status Request 97
- General Specifications 100
- MS-2 CCD Reader Dimensions 100
- Appendices 101
- Serial Configuration Commands 104
- Serial Command Format 105
- Appendix E — ASCII Table 108
- Appendix F — Operational Tips 109
- 5 Volt Devices 110
- 10-28 Volt Devices 110
- Hyperlink Index 115
- Variable Length 124
- Very Large-Scale Integration 124
- Warranty 124
- Recipient Response 125
Relacionado con productos y manuales para Lectores De Códigos De Barras Microscan MS-2
(431 paginas)
(2 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales