Microscan MS-96 Manual de usuario descargar pdf (Pagina 177)

Chapter 12 Utilities

MS-9 Scanner User’s Manual 12-19

Autodiscrimination

You can enable most or specific symbol types by the following operational commands.

Default: Code 39 (only)

Options: <P> Enables most symbol types.

<Q> Enable Code 39 only

<R> Enable Codabar only

<S> Enable I 2/5 only

1 2 ... 172 173 174 175 176 177 178 179 180 181 182 ... 225 226

MS-9 Scanner 1
User's Manual 1
Disclaimer 2
Latest Manual Version 2
What Is Covered? 3
What Is Excluded? 3
Limitation of Liability 3
Table of Contents 4
Chapter 7 OMR 5
Chapter 8 I/0 Parameters 5
Chapter 9 Diagnostics 5
Chapter 10 Laser Control 5
Chapter 11 Terminal Mode 6
Chapter 12 Utilities 6
List of Figures 7
List of Tables 8
About the MS-9 Scanner 9
About This Manual 10
Host Communications 10
Approvals 11
Safety Labels 11
Warning and Caution Summary 12
Quick Start 13
Step 1 — Hardware Required 14
Step 2 — Connect the System 15
Step 3 — Install ESP 16
Step 4 — Select Scanner Model 17
Step 5 — Autoconnect 18
Chapter Quick Start 19
Step 7 — Test for Read Rate 20
By Serial Commands 21
By Embedded Menu 21
Configure the Scanner 22
Using ESP 23
Setup Mode 24
Application Mode 25
Pulldown Menus 26
Chapter 2 Using ESP 27
Making Changes in ESP 29
Send/Receive Options 30
Communications 31
Communications by ESP 32
RS-232/422 Host Port 33
Host Protocol 34
Point-to-Point with RTS/CTS 35
Polling Mode D 35
User Defined Point-to-Point 36
Chapter 3 Communications 37
Host RS-422 Status 38
RS-232 Auxiliary Port 39
Aux Port Mode 40
Transparent Mode 41
Half Duplex Mode 41
Full Duplex Mode 43
Daisy Chain ID 44
Preamble 45
Postamble 46
LRC Status 47
Response Timeout 48
Intercharacter Delay 48
Read Cycle 49
Read Cycle by ESP 50
Read Cycle by Serial Command 51
Multisymbol 52
Chapter 4 Read Cycle 53
Trigger Mode 54
Continuous Read 1 Output 55
External Trigger Level 56
External Trigger Edge 57
Serial Data 58
Serial Data or Edge 58
Trigger Filter 59
Duration 59
External Trigger State 59
Serial Trigger 60
End of Read Cycle 61
Timeout or New Trigger 62
Read Cycle Timeout 63
Good Decode Reads 64
Scanner Setup 65
Automatic Gain Control (AGC) 66
Video Settings 67
Laser Setup 68
Symbologies 69
Symbologies by ESP 70
Symbologies by Serial Command 71
Code 39 Status 72
Check Digit Status (Code 39) 72
Symbol Length (Code 39) 73
Full ASCII Set (Code 39) 74
Code 128 75
Interleaved 2 of 5 76
Chapter 5 Symbologies 77
Codabar Status 78
Symbol Length (Codabar) 79
Check Digit Type (Codabar) 80
UPC/EAN Status 81
EAN Status 81
Separator Status (UPC/EAN) 82
Separator Character (UPC/EAN) 83
RSS Expanded 84
RSS Limited 85
RSS-14 Status 86
Narrow Margins 87
Symbology Identifier 88
Background Color 89
Autodiscriminate 90
Matchcode 91
Matchcode by ESP Menu 92
Matchcode by Serial Command 92
Overview of Matchcode 93
Using Master Symbols 93
Matchcode Type 94
Sequential Matching 95
Match Start Position 95
Match Length 96
Wild Card 96
Sequence On Noread 97
Sequence On Mismatch 98
New Master Pin 100
(Optical Mark Recognition) 101
Chapter Contents 101
OMR Setup by ESP Menu 102
OMR Setup by Serial Command 102
OMR Description 103
OMR Definitions 104
Chapter 7 OMR 105
OMR Setup 106
Number of Fields 107
Trigger Delay Type 108
Number of Scans 108
Gate Bar Location 109
Trigger Delay 109
Output Style 109
Static Test 110
Dynamic Calibration 111
Calibration Data 112
Auto Frame Status 113
Average Bar Width 113
Average Cell Width 113
Leading Margin 113
Scan Count 114
Laser Control 115
I/0 Parameters 117
I/O Parameters by ESP 118
Symbol Data Output 119
When to Output Symbol Data 121
Noread Message 122
Beeper Status 123
Partial Output 124
Serial Verification 125
Operation Command Output 126
Output 1 Parameters 127
Active State 128
Pulse Width 128
Output Mode 129
Trend Analysis Mode 130
Trigger Evaluation Period 131
Number to Output On 131
Decodes per Trigger 131
Output 2 Parameters 132
Output 3 Parameters 132
Quality Output 133
Diagnostics 135
Diagnostics by ESP Menu 136
Diagnostics by Serial Command 137
Power-on 138
Hours Since Reset 139
Warning Messages 140
Laser High 141
Laser Low 142
Chapter 9 Diagnostics 143
High Temperature Threshold 144
Low Temperature Threshold 145
Lifetime Hours 146
Laser Control by ESP Menu 148
Laser On/Off 149
Laser Framing 150
Laser Off Time 151
Laser On Time 152
Terminal Mode 153
Terminal Window 154
Find Function 155
Editing a Macro 156
Terminal Window Functions 157
Utilities 159
Utilities by ESP Menu 160
Utilities by Serial Command 161
Read Rate 163
Counters 165
Counters by Serial Command 166
Device Control 167
Master Database 169
Enter Master Symbol Data 170
Chapter 12 Utilities 171
Request Master Symbol Data 172
Delete Master Symbol Data 173
Firmware 174
By Serial Command 175
Autodiscrimination 177
Scanner Status Requests 178
Appendices 179
General Specifications 180
FIS Options 181
LED Indicators 182
Electrical Specifications 184
Optoisolator Outputs 185
Output Circuit Examples 185
Optoisolator Inputs 187
IB-131 Interface Module 188
Scanner to IB-131 189
Multidrop 190
Daisy Chain 190
Serial Configuration Commands 192
Serial Utility Commands 194
Serial Command Status Request 195
Appendix F — ASCII Table 196
Appendix G — Embedded Menus 198
Defaulting 199
Initialize 200
Initializing 202
Loss of Communications 202
Appendix I — Test Decode Rate 203
Scan line 205
Figure A-11 Angled 206
Picket Fence 206
Appendix K — Operational Tips 208
Configure the Scanner for 210
Polling Sequence 212
Select Sequence 213
Multidrop Communications 214
Glossary of Terms 216
MS-9 Scanner User’s Manual 222

Comentarios a estos manuales

Sin comentarios

Microscan MS-96 Manual de usuario Pagina 177

Comentarios a estos manuales

Relacionado con productos y manuales para Lectores De Códigos De Barras Microscan MS-96