Microscan MS-4X Manual de usuario Pagina 230
- Pagina / 312
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Counts
15-12 MS-880 Industrial Long Range Scanner User’s Manual
15–Diagnostics
Counts
(These commands are READ ONLY.)
Powerups
Resets
Definition Returns the number of times the scanner has been re-powered or a
watchdog reset occurs.
Usage: Useful for detecting unwanted resets caused by power supply problems
or ESD transients.
Serial Cmd: Send <K406?>
Returns <K powerups,resets>
Read Only
Ranges:
0 to 65,535 powerups, 0 to 65,535 resets.
Definition Resets include watchdog reset, <A>, <Z>, <Zd>, and hardware
defaults. A watchdog reset is a reset that is forced whenever the soft-
ware locks-up.
Usage: Useful for detecting unwanted resets caused by power supply problems
or ESD transients.
Serial Cmd: Send <K406?>
Returns <K powerups,resets>
Read Only
Ranges:
0 to 65,535 powerups, 0 to 65,535 resets.
- Industrial 1
- Long Range Scanner 1
- User's Manual 1
- Table of Contents 4
- List of Tables 9
- About This Manual 10
- Host Communications 10
- Keystrokes 11
- Approvals 11
- Safety Labels 12
- Warning and Caution Summary 13
- Quick Start 15
- Step 1 — Hardware Required 16
- Step 2 — Connect the System 17
- 1–Quick Start 18
- Chapter 1 Quick Start 19
- Step 3 — Install ESP-MP 20
- Step 4 — Select Scanner Model 21
- Communications 31
- Communications Options 32
- Communications 33
- Communications by ESP 33
- 2–Communications 34
- Host Port Parameters 35
- Data Bits, Host Port 36
- RS422 Status 37
- Auxiliary Port 38
- Tra ns par en t Mo d e 39
- Half Duplex Mode 40
- Full Duplex Mode 41
- Daisy Chain Mode 42
- Command Processing Mode 43
- Baud Rate, Aux Port 44
- Parity, Aux Port 44
- Data Bits, Aux Port 44
- Daisy Chain Autoconfigure 46
- Daisy Chain Remote Scanner ID 47
- IrDA Port 48
- Menu Mode 49
- Protocol 51
- Protocol by ESP 52
- Protocol by Serial Command 52
- Protocol 53
- Protocol by Embedded Menu 53
- Point-to-Point with RTS/CTS 55
- Polling Mode D 55
- Multidrop 56
- User Defined Point-to-Point 56
- User Defined Multidrop 58
- Response Timeout 60
- Intercharacter Delay 61
- Output Data Format 62
- Postamble Characters 63
- Auxiliary Status 64
- Configuration Status 64
- Network Client 65
- 3–Protocol 66
- Read Cycle/Trigger 67
- Read Cycle/Trigger by ESP 68
- Read Cycle/Trigger 69
- Trigger Mode 70
- Continuous Read 1 Output 71
- External Trigger Level 72
- External Trigger Edge 73
- Serial Data 74
- Serial Data or External Edge 74
- Network Trigger 74
- Trigger Filter Duration 75
- Good Decode Reads 75
- Serial Trigger 76
- External Trigger State 78
- End of Read Cycle 79
- 4–Read Cycle/Trig 80
- Timeout Duration 81
- Multilabel 82
- Multilabel Separator 83
- Code Types by ESP 86
- Code Types by Serial Command 87
- Code Types by Embedded Menu 88
- Narrow Margins 89
- Symbology ID 90
- Background Color 91
- Code 39 Status 92
- Check Digit Status (Code 39) 92
- Check Digit Output (Code 39) 92
- Fixed Code Length (Code 39) 93
- Full ASCII Set (Code 39 94
- Codabar Status 95
- Fixed Code Length (Codabar) 96
- Check Digit Type (Codabar) 97
- Check Digit Output (Codabar) 97
- Interleaved 2 of 5 100
- UPC Status 101
- EAN Status 101
- Separator Status (UPC/EAN) 102
- Separator Character (UPC/EAN) 103
- Supplementals Type (UPC/EAN) 103
- PDF417 Status 104
- Fixed Code Length (PDF417) 104
- (PDF417) 105
- Code 128 106
- UCC/EAN-128 107
- Chapter 5 Codes 109
- Code 93 Status 110
- Fixed Code Length (Code 93) 110
- Pharma Code 111
- Bar Widths (Pharma Code) 112
- Autodiscriminate 113
- Autocalibration 115
- Overview of Autocalibration 116
- Autocalibration 117
- Autocalibration Steps 117
- Autocalibration by ESP 118
- 6–Autocalibration 120
- Auto Range 120
- Scanner Settings 123
- Autocalibration Menu Options 124
- Calibration 127
- Database 127
- 7–Calibration Data 128
- Calibration with Multilabel 128
- Calibration Database by ESP 129
- Database Index 130
- Focus Position 130
- Tra ck in g 130
- Calibration Database 131
- Request Database Settings 131
- Optoelectrics 133
- Optoelectric by ESP 134
- Optoelectrics 135
- Overview of Optoelectrics 136
- Optoelectric Database Modes 137
- Timer Mode 138
- Automatic/Static Mode 138
- Control Trigger Mode 139
- 8–Optoelectrics 140
- Control Trigger #1 141
- Control Trigger #2 141
- Control Trigger #3 141
- Latch on Trigger 142
- Timer Value 143
- Raster/Laser 145
- Raster Setup 147
- Bottom Offset 148
- Raster/Laser Control 149
- Raster Sweep Rate 149
- Laser Setup 150
- Laser Framing Status 151
- Laser Off Time 152
- Laser On Time 152
- Laser Power 152
- Raster/Laser by Embedded Menu 153
- Scanner Setup 155
- Scanner Setup by ESP 156
- Scanner Setup 157
- Scan Speed 158
- Zero Position 159
- Gain Adjustment 160
- Tracking 160
- Transition Counter 161
- Maximum Element 162
- Matchcode 163
- Matchcode by ESP 164
- Matchcode by Serial Command 164
- Matchcode 165
- Matchcode by Embedded Menu 165
- Overview of Matchcode 166
- Matchcode Type 167
- Sequential Matching 168
- Match Start Position 168
- Match Length 169
- Wild Card Character 169
- Sequence On Noread 170
- Sequence On Mismatch 171
- 11–Matchcode 172
- Sequence Step 172
- Master Label Database 173
- Enter Master Label Data 174
- Request Master Label Data 175
- Request All Master Label Data 175
- Delete Master Label Data 176
- New Master Pin 178
- 12–Outputs 179
- Chapter Contents 179
- Outputs by Serial Command 180
- Outputs by Embedded Menu 180
- Outputs 181
- Output Data by ESP Menu 181
- Noread Message 182
- Bar Code Output 183
- When to Output Bar Code Data 184
- Serial Verification 186
- Control/Hex Output 187
- Beeper Status 188
- Quality Output 189
- Output Format 191
- 13–Output Format 192
- Output Format and Filtering 193
- Output Format Status 194
- Extraction Mode 195
- Extraction by Serial Command 196
- Insertion Mode 197
- Insertion by Serial Command 198
- Advanced Output Format by ESP 199
- Output Format Status by ESP 200
- Ordered Output/Filtering 201
- Filter # 202
- Code Type 202
- Number of Filters 204
- Master Database in ESP 206
- Discrete I/0 207
- Discrete I/O by ESP Menu 208
- Discrete I/0 209
- Input Mode 210
- Active State 210
- Output 1 211
- Pulse Width 212
- Output Mode 213
- Trend Analysis Mode 214
- Trigger Evaluation Period 215
- Number Before Output 215
- Reads per Trigger Threshold 215
- Output 2 216
- Output 3 216
- Diagnostic Outputs 217
- 14–Discrete I/0 218
- Diagnostics 219
- Diagnostics by ESP Menu 220
- Diagnostics by Serial Command 220
- Diagnostics 221
- Diagnostics by Embedded Menu 221
- Warning Messages 222
- Laser High Warning 223
- Laser Low Warning 224
- NOVRAM Corrupt Warning Status 225
- High Temperature Threshold 226
- Low Temperature Threshold 227
- Lifetime Hours 228
- Powerups 230
- Time Since Last Reset 231
- 15–Diagnostics 232
- Wiring Box Option 233
- Wiring Box Description 234
- Installation Steps 235
- 16–Wiring Box 236
- Wiring Box Ports 237
- Chapter 16 Wiring Box Option 239
- Figure 16-7 Wiring Box PCB 240
- Mounting Plate 241
- Utilities 243
- Utilities by ESP Menu 244
- Utilities 245
- Utilities by Serial Command 245
- 17–Utilities 246
- File Transfer 247
- Counters 248
- Part Number 250
- Checksum 251
- Read Rate 252
- Device Control 254
- Appendices 257
- Centerline of scan window 258
- , IrDa port** 259
- Table A-1 MS-880 FIS Options 259
- Table A-2 MS-880 Read Ranges 259
- Appendix A 260
- Mounting Specifications 260
- LED Indicators 260
- General Specifications 261
- Safety Certifications 261
- Appendix B 262
- Pin Assignments 262
- Electrical Specifications 263
- Optoisolator Outputs 265
- Optoisolator Inputs 267
- IrDA Configuration Port 269
- Serial Menu: 269
- IrDA Status 269
- Appendix C 270
- IR Timeout 270
- Embedded Menu Mode 270
- IrDA/Ir Comm for Palm Pilot 271
- Obtaining the drivers: 271
- Installing the drivers: 271
- Appendix E 272
- Serial Configuration Commands 273
- Serial Command Format 275
- Serial Utility Commands 275
- Control Characters 276
- Appendix G — ASCII Table 277
- Appendix G 278
- Appendix H — Embedded Menus 279
- Defaulting 280
- Appendix I 282
- Initializing 283
- Loss of Communications 283
- Appendix J 284
- Position Object Detector 285
- With a Static Label 286
- Number of Decodes 286
- With a Moving Label 286
- Direction of label travel 287
- Scan Line 287
- Raster pattern 288
- Appendix M 290
- Appendix N — Operational Tips 291
- Interface Standards 293
- ProfiBus DP 293
- Modicon Ethernet 293
- Appendix P 294
- Multidrop Communications 295
- Polling Sequence 296
- Select Sequence 297
- Glossary of Terms 299
- Appendix Q 300
- Numerics 305
- Tracking 7-4, 10-6, A-34 311
Relacionado con productos y manuales para Lectores De Códigos De Barras Microscan MS-4X
(156 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales